Calibrating your Z-Offset

Your Me2 is factory calibrated and tested when it arrives. You DO NOT need to run through this calibration process unless your prints are failing due to some change that has occurred in transit. Submit a support request for further advice if you are suffering out-of-the-box failures. 

The Z-Offset defines the actual height difference between the limit switch on the extruder head and the extruder nozzle. It’s an important number that can be the difference between a perfect print and a squiggly pile of plastic spaghetti.

You shouldn’t need to calibrate your Z-Offset often, only when a change to the extruder has occurred. Please note that a new Me2 fresh out of the box is already calibrated. Still, you may need to tweak your offset from time to time due to wear, transport or part replacement.

Note: You will need to be using an account with admin privileges to perform a Z-Offset calibration.

Step 1 - Access the Z-Offset calibration tool

- Access your list of printers at the top of the BuildBee interface.

- Click on the 'MAINTENANCE' button next to the printer you wish to calibrate.

- Select 'MAINTENANCE' and then 'START CALIBRATION'. 

Step 2 - Run the Z-Offset calibration tool

- After selecting the 'START CALIBRATION' button wait for the printer to heat up. Once the printer has reached the target temperature, it will move to the ready position.

- Use the 'TEST' button to test the print height. The printer will produce a long, thin box and then a single line in the centre of the box, which should fill the shape. 

In some cases, it is a good idea to raise the Z-Offset first to avoid any dragging on the print bed.

Step 3 - Adjust the Z-Offset accordingly

- Use the 'HIGHER' or 'LOWER' buttons to adjust the print height. 

By default, the adjustment size is 0.1mm. You can set the adjustment size to either 0.1mm or 1mm. To keep track of each adjustment that you make, there is a counter that will display the Current Net Adjustment that you've made in millimetres. Avoid clicking multiple times in quick succession; this can result in your Z-Offset value being thrown out in the software, which can cause issues with calibration.

- After each adjustment, click the 'TEST' button to draw another calibration strip. A good calibration strip will not have any gaps between the lines, are flat to the touch with no obvious bumps and stick well to the print bed without being difficult to remove. 

Too high - There will be big gaps between lines and bed adhesion will be poor.

Too low - Flow of plastic will be restricted and anything printed will be difficult to remove from the bed.

- Select 'FINISH CALIBRATION' to return to the maintenance console. 

 

Step 4 - Run a test print (optional)

- We recommend running a small print to test your new settings in action. We recommend printing a Cali-mouse from our 'Featured Models' section on the home page.

- Pay attention to the first few layers of the print. Look for the same indicators of good/bad calibration in the model that you are testing.

• Related Articles

• Z-Offset did not calibrate properly

  Make sure your BuildBee is running the latest version.   If you are still experiencing issues with your Z-Offset being too high/low even after calibrating it, something may have gone wrong during the calibration process. While it is an uncommon ...

• How to tighten a loose feed tube

  Only run through the steps in this article if you have already tried calibrating the Z offset and have checked the Z axis belt. If you are still encountering a low Z offset after checking these things, it may be worth running through the ...

• Nozzle Height

  Having the correct extruder nozzle height is essential for high quality 3D printing. If the extruder nozzle is too high, your filament will extrude into the air, leading to poor adhesion onto the print bed and poor print quality. Having the extruder ...

• Orienting models for 3D printing

  One of the most important aspects of design for 3D printing is how the model is oriented. It can mean the difference between a failure and a successful print. Keep the following things in mind when designing/checking your model: Models will print ...

• Extruder Makes a Clunking Sound

  The clunking sound comes from the stepper motor in the extruder head skipping because it’s overloaded - in other words it’s taking too much effort to push fresh filament into the hot-end, melt it and extrude it onto the build surface. This can result ...